Search found 34657 matches
- Fri May 24, 2024 11:35 pm
- Forum: Maintenance and Repair
- Topic: VFD for 3 phase motor
- Replies: 3
- Views: 95
Re: VFD for 3 phase motor
No experience here, but I question the assumption that a 3 phase induction motor is tolerant of a wide frequency range. Or the 3 phase converter as well.
- Fri May 24, 2024 11:13 pm
- Forum: Beginning Woodworking
- Topic: need help, what is thI s
- Replies: 15
- Views: 710
Re: need help, what is thI s
I believe the subject is quill shaft set screws. I can agree that drive hubs on either rear shaft or SPTs need to be cup or serrated cup tips.
Other locations used for holding parts in assemblies also need to be cup . . .
Not yet mentioned is proper length will vary.
Other locations used for holding parts in assemblies also need to be cup . . .
Not yet mentioned is proper length will vary.
- Thu May 16, 2024 3:12 am
- Forum: Woodworking Tool Review
- Topic: Power Pro Gen 2 -- now with typos!
- Replies: 9
- Views: 19230
Re: Power Pro Gen 2 -- now with typos!
My take on funky English/spelling is inexcusable since a serious review of the product will reveal all(assuming the reviewer is functionally literate with the language(and the intended purpose of the product)).
- Thu May 16, 2024 3:02 am
- Forum: Maintenance and Repair
- Topic: Scroll Saw Bushing puller - JPG inspired
- Replies: 5
- Views: 950
- Thu May 16, 2024 2:52 am
- Forum: Maintenance and Repair
- Topic: Emerson 1 1/8 hp start switch
- Replies: 3
- Views: 225
Re: Emerson 1 1/8 hp start switch
One can always add a manually operated external switch. Not recommended but it is a work around.
- Thu May 16, 2024 2:49 am
- Forum: Beginning Woodworking
- Topic: need help, what is thI s
- Replies: 15
- Views: 710
Re: need help, what is thI s
While we be on the subject of set screws, do be aware that cup tip and serrated cup screws are to be avoided. Flat or oval tip are the proper choice.
- Tue May 14, 2024 12:12 am
- Forum: Maintenance and Repair
- Topic: 10ER motor spins both ways
- Replies: 3
- Views: 173
Re: 10ER motor spins both ways
I be guessing here (this is a most unusual experience) 1) the motor has a natural tendency to start in one direction when the start circuit is ineffective.(a logical conclusion given the problem) 2) that natural tendency reverses occasionally due to factor(s) unknown. 3) by placing the motor in rota...
- Sun May 12, 2024 4:48 am
- Forum: Community
- Topic: Heads Up - Bargain 'available'
- Replies: 2410
- Views: 3744510
Re: Heads Up - Bargain 'available'
The "holes" in the tube rails are an early model distinction and applies to both the 505 and 510. The early version had tapped holes in the tables thus making them non adjustable.
- Sun May 12, 2024 4:20 am
- Forum: Beginning Woodworking
- Topic: need help, what is thI s
- Replies: 15
- Views: 710
Re: need help, what is thI s
An adapter sleeve works IF one includes a notch for the set screw to fully contact the bit shank. BTDT A bronze bushing bearing seems to have close enough dimensions.
- Tue May 07, 2024 2:55 pm
- Forum: Maintenance and Repair
- Topic: Wax tip.
- Replies: 17
- Views: 18803
Re: Wax tip.
What is needed is carnauba wax. As for scent, that comes from whatever solvents are used. A simpler replacement is paste finishing wax(minwax) JPW was a paste FLOOR wax. Original was slippery so later floor waxes were 'de slipperyiezed'. From looking at the ingredients I would not recommend Jubilee.