Search found 87 matches
- Fri Dec 09, 2016 12:26 pm
- Forum: General Woodworking
- Topic: Farmhouse Table
- Replies: 28
- Views: 31733
Farmhouse Table
Ok guys, I've picked my first woodworking project with the ShopSmith - and it will only be my second woodworking project to date (the first was a Shaker book case via Family Handyman plans that I built about 5 years ago). This time around its a new table for the breakfast area. With 4 kids plus the ...
- Mon Dec 05, 2016 5:23 pm
- Forum: Maintenance and Repair
- Topic: 1986 Mark V 510, USGI
- Replies: 9
- Views: 8932
Re: 1986 Mark V 510, USGI
Thanks everyone. The quill set screw must have been the original one, it was covered with a wax plug which was painted over in the original gray of the headstock. Given the burr and the bent spline end of the drive shaft, I believe I'm going to replace the entire quill assy I'll keep an eye on the s...
- Sat Dec 03, 2016 8:01 am
- Forum: Maintenance and Repair
- Topic: 1986 Mark V 510, USGI
- Replies: 9
- Views: 8932
Re: 1986 Mark V 510, USGI
Problem #3 quill 'bent?' Is it bent, or does it merely wobble. Will the drive sleeve end move sideways if pushed? Problem #2 quill burrs. Yes do gently file them away. Also make sure the sides of the keyway are also not burred. When inserting the quill back into the headstock, make sure the half do...
- Sat Dec 03, 2016 12:15 am
- Forum: Maintenance and Repair
- Topic: 1986 Mark V 510, USGI
- Replies: 9
- Views: 8932
Re: 1986 Mark V 510, USGI
By the way I'm located in Youngsville, North Carolina - just north of Raleigh.
Does SS sell any service parts through a dealer network? I see SS abbrasives at my local Lowes but haven't checked with the local woodworking shops on local parts availability.
Does SS sell any service parts through a dealer network? I see SS abbrasives at my local Lowes but haven't checked with the local woodworking shops on local parts availability.
- Sat Dec 03, 2016 12:02 am
- Forum: Maintenance and Repair
- Topic: 1986 Mark V 510, USGI
- Replies: 9
- Views: 8932
Re: 1986 Mark V 510, USGI
Congratulations and welcome to the insanity. You have a model 510. The burrs on the quill can be removed by some judicious filing with some fine jewelers files. If you can feel the burr with your fingers you should remove it. The gouge inside the headstock bore is a bit more perplexing. My guess wo...
- Fri Dec 02, 2016 7:49 pm
- Forum: Maintenance and Repair
- Topic: 1986 Mark V 510, USGI
- Replies: 9
- Views: 8932
1986 Mark V 510, USGI
Hi folks, this is my first real post here and I thought I'd share some photos of the Mark V I just bought and ask a few questions (SS newbie here). From the serial plate it's a Model 510 and the S/N indicates a 1986 model. This unit was used by the USAF on Seymore Johnson Air Force Base and then auc...
- Fri Dec 02, 2016 1:27 pm
- Forum: Maintenance and Repair
- Topic: rust on way tubes and other parts
- Replies: 32
- Views: 30605
Re: rust on way tubes and other parts
I'm also curious about oxalic acid -- which you can pick up anywhere under the name "Barkeeper's Friend" -- works great on SS and aluminum pots/pans, SS bar tops, etc.
I just picked up a Mark V from C-list and the bench tubes have a light petina that I'd like to get off.
I just picked up a Mark V from C-list and the bench tubes have a light petina that I'd like to get off.