Search found 14 matches
- Mon Dec 23, 2019 4:44 pm
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
Just wanted to get back to the group with an update. At long last I have the ShopSmith back up and running again!!! I replaced the bent motor sheave and also got a new cone point allen screw in the eccentric holding tightly the groove in the idler shaft pulley. Tight but not too tight ;) I also perf...
- Thu Nov 14, 2019 10:39 am
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
Just an update, Yesterday I made a careful inspection of the motor sheaves. It seems that I must have damaged the floating sheave when I was trying to free it up and get it sliding on the motor shaft. There is for sure a visible dent on the outer rim which I attribute to over zealous blows with a no...
- Wed Nov 13, 2019 12:05 pm
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
Eric (ednspace): I am happy to see that the Sawdust Sessions and Video Tips (under Woodworking Resources) are now back up and available. In addition to all of the other great sources of information out there, these may be helpful as you work to determine how to get your machine back in peak conditi...
- Tue Nov 12, 2019 9:46 am
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
Ok... Had a little time today to shoot a video of my machine running. I tried to use the same format as br549. It gets pretty loud near the high speed end. It's really kind of nerve racking. I will try and share this video via a DropBox link also... https://www.dropbox.com/s/24t9dy16vpgqwl3/ShopSmi...
- Tue Nov 12, 2019 9:39 am
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
In the second image (showing the bearing, washer and screw), the bearing is protruding further than it should. The washer is intended to prevent the bearing from doing what you see there. The idler shaft needs to be relocated. Reference my earlier post. That is NOT normal. Perform a high speed adju...
- Tue Nov 12, 2019 9:34 am
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
The rubber dust is interesting. You said that you worked on the sheaves where the belt rides. Are the edges of the contact surface of the sheaves sharp? You may want to take the sharp edges off them so the belt doesn't wear prematurely. Also check for a slightly bent sheave. You may have to turn th...
- Tue Nov 12, 2019 9:33 am
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
The rubber dust is interesting. You said that you worked on the sheaves where the belt rides. Are the edges of the contact surface of the sheaves sharp? You may want to take the sharp edges off them so the belt doesn't wear prematurely. Also check for a slightly bent sheave. You may have to turn th...
- Tue Nov 12, 2019 9:23 am
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
Thanks Bill, hope to have one coming from Fastenal, all I could find at McMaster was 3/8" but it's possible I overlooked it...wa2crk wrote:That set screw is a cone point type and should be available from McMaster-Carr on the net
Bill V
Here is the part number that I found - 0176636
- Mon Nov 11, 2019 5:40 pm
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
Ok... Had a little time today to shoot a video of my machine running. I tried to use the same format as br549. It gets pretty loud near the high speed end. It's really kind of nerve racking. I will try and share this video via a DropBox link also... https://www.dropbox.com/s/24t9dy16vpgqwl3/ShopSmit...
- Sun Nov 10, 2019 10:28 am
- Forum: Maintenance and Repair
- Topic: Inherited ShopSmith With Noise Issue
- Replies: 29
- Views: 31405
Re: Inherited ShopSmith With Noise Issue
Thank you - JPG I get it. Cone point set screw centers the bearing, washer positions the eccentric. I may have found a source for the set screw and if I can get one I think I can get these two pieces back in place correctly. Thinking of the cone point set screw as a positioner rather then a hold dow...