Jointer fence doesn't lock in place
Moderators: HopefulSSer, admin
Jointer fence doesn't lock in place
I've recently bought a used SS jointer. I took the fence off the mounting bar to thoroughly clean the table. But, when I put the the fence back on the mounting bar, I couldn't get it to lock in place. The angle of the fence will lock when I tighten down the handle but, the fence doesn't lock on the mounting bar even though the handle is tightened down to hold the fence angle. Is there a piece or part that I may have misplaced?
-
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Jointer fence doesn't lock in place
The tightening lever is double acting, I believe you push it in to tight/loosen the fence on the bar, and pull it away to tighten or loosen the fence to change the angle. Or totally vice a versa.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
Re: Jointer fence doesn't lock in place
I found out the problem. I wasn't pulling the dual purpose handle out far enough to engage the locking of the fence on the mounting bar. Duh...what a senior moment!
- JPG
- Platinum Member
- Posts: 34648
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Jointer fence doesn't lock in place
Vice versa!!!ERLover wrote:The tightening lever is double acting, I believe you push it in to tight/loosen the fence on the bar, and pull it away to tighten or loosen the fence to change the angle. Or totally vice a versa.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Jointer fence doesn't lock in place
Thanks John Paul Getty for the correction, non here at moms to check which way it was.
Dafixer there is also a pin that can be inserted to go back to 90*, so if you get to a situation that the fence angle does not want to go/move, dont force it, look for the pin and I think pull it out. I will get corrected on that but thats OK, since I cant check one at the moment and dont use one regularly.
Dafixer there is also a pin that can be inserted to go back to 90*, so if you get to a situation that the fence angle does not want to go/move, dont force it, look for the pin and I think pull it out. I will get corrected on that but thats OK, since I cant check one at the moment and dont use one regularly.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
- JPG
- Platinum Member
- Posts: 34648
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Jointer fence doesn't lock in place
No 'pin', but a small headless screw and a flip plate stop.ERLover wrote:Thanks John Paul Getty for the correction, non here at moms to check which way it was.
Dafixer there is also a pin that can be inserted to go back to 90*, so if you get to a situation that the fence angle does not want to go/move, dont force it, look for the pin and I think pull it out. I will get corrected on that but thats OK, since I cant check one at the moment and dont use one regularly.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Jointer fence doesn't lock in place
Yep, found the "flip" plate too.
Thanks guys for your help and instructions.
Thanks guys for your help and instructions.
-
- Bronze Member
- Posts: 1
- Joined: Wed Jul 12, 2017 3:00 pm
Re: Jointer fence doesn't lock in place
Thanks for the tip of the double acting handle on the joiner. Took a lot longer to register with Shopsmith than it did to find out how to lock the fence.Very helpful.
-
- Gold Member
- Posts: 320
- Joined: Fri Sep 11, 2015 5:46 pm
Re: Jointer fence doesn't lock in place
the hollow tube should have a dowel in it. When you tighten the screw it contacts the bar and holds it. Do not over tighten as it will strip the threads out and want work at all. Think it is 3/16 dia by 3/4 0r 7/8 long. Easy fix. Use a dowel or a bolt with head removed.
- JPG
- Platinum Member
- Posts: 34648
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Jointer fence doesn't lock in place
The back side that grips the bar is fairly soft(cast aluminum) and excessive tightening will deform it.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange