Arbors
Moderators: HopefulSSer, admin
Arbors
While looking through my Shopsmith drawer I found an extra 5/8" arbor that I'm not sure exactly what it is.
I have one of the Shopsmith 5/8" molder/dado arbors listed here and I know what that one is.
http://www.shopsmith.com/ownersite/cata ... oarbor.htm
The extra one is very similar, but a bit shorter, 1/8-1/4" less on the bolt end. It doesn't have the 3/4" thick washer that the molder/dado arbor has, and it lacks the groove in the bolt for the locking tongue washer. It has been with my Shopsmith for decades, but I don't remember what it is for. I have used it with my wobble dado, but it isn't quite long enough for my multi-blade dado when set to maximum width. Is it maybe just an earlier version of the molder/dado arbor?
I have one of the Shopsmith 5/8" molder/dado arbors listed here and I know what that one is.
http://www.shopsmith.com/ownersite/cata ... oarbor.htm
The extra one is very similar, but a bit shorter, 1/8-1/4" less on the bolt end. It doesn't have the 3/4" thick washer that the molder/dado arbor has, and it lacks the groove in the bolt for the locking tongue washer. It has been with my Shopsmith for decades, but I don't remember what it is for. I have used it with my wobble dado, but it isn't quite long enough for my multi-blade dado when set to maximum width. Is it maybe just an earlier version of the molder/dado arbor?
Re: Arbors
that arbor is for 3rd party saw blades with 5/8th arbor, which are more common.
- dusty
- Platinum Member
- Posts: 21368
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Arbors
Good and logical guess but how do we know that without having seen the arbor in question.jjj240 wrote:that arbor is for 3rd party saw blades with 5/8th arbor, which are more common.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Re: Arbors
If it was for saw blades, something is missing because there aren't enough threads on it to turn it down far enough to tighten on a saw blade. I can turn it down to about 3/8" until it runs out of threads, and up to abuot 3/4" until I run out of bolt. I would need some kind of spacer to tighten it on a standard saw blade.jjj240 wrote:that arbor is for 3rd party saw blades with 5/8th arbor, which are more common.
Re: Arbors
Not for saw blades!!! For other 5/8 stuff like buffing wheels and wire wheels etc. Only put saw blades on saw blade arbors the others are not suited for saw blades and can be dangerous if used that way.
Bill V
Bill V
Re: Arbors
You say it is a bit shorter. How long is it? The current molder/dado arbor shaft is 1 15/16" long. The thick washer is 5/8" thick. How wide can you set your multi blade dado? The max on the SS dado is 3/4" with the stock set.garys wrote:While looking through my Shopsmith drawer I found an extra 5/8" arbor that I'm not sure exactly what it is.
I have one of the Shopsmith 5/8" molder/dado arbors listed here and I know what that one is.
http://www.shopsmith.com/ownersite/cata ... oarbor.htm
The extra one is very similar, but a bit shorter, 1/8-1/4" less on the bolt end. It doesn't have the 3/4" thick washer that the molder/dado arbor has, and it lacks the groove in the bolt for the locking tongue washer. It has been with my Shopsmith for decades, but I don't remember what it is for. I have used it with my wobble dado, but it isn't quite long enough for my multi-blade dado when set to maximum width. Is it maybe just an earlier version of the molder/dado arbor?
First, I think you are just missing the thick washer. As for the key way. Does anyone know if the 10ER arbor had a key way. Looking at the 10ER accessory catalog that arbor is basically the same as the current arbor but the catalog says the thick washer is 3/4". Does anyone have a known 10ER arbor and does it have a key way. It is hard to tell from the picture in the catalog but using a magnifying glass it looks like it has a key way. However, the catalog is dated 1953, the end of 10ER production. Maybe the first/early arbor had no key way.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: Arbors
This is the arbor that came with my 10ER, it is what I use with my saw blade.jsburger wrote: First, I think you are just missing the thick washer. As for the key way. Does anyone know if the 10ER arbor had a key way. Looking at the 10ER accessory catalog that arbor is basically the same as the current arbor but the catalog says the thick washer is 3/4". Does anyone have a known 10ER arbor and does it have a key way. It is hard to tell from the picture in the catalog but using a magnifying glass it looks like it has a key way. However, the catalog is dated 1953, the end of 10ER production. Maybe the first/early arbor had no key way.
Total length 3 1/8, shaft length 1 5/8, keyed shaft and washer. and with the blade mounted.
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
Re: Arbors
Interesting! The 1953 accessory catalog lists a 3/4" spacer and TWO 3/16" spacers. The two 3/16" spacers are clearly visible in the picture of the arbor.rpd wrote:This is the arbor that came with my 10ER, it is what I use with my saw blade.jsburger wrote: First, I think you are just missing the thick washer. As for the key way. Does anyone know if the 10ER arbor had a key way. Looking at the 10ER accessory catalog that arbor is basically the same as the current arbor but the catalog says the thick washer is 3/4". Does anyone have a known 10ER arbor and does it have a key way. It is hard to tell from the picture in the catalog but using a magnifying glass it looks like it has a key way. However, the catalog is dated 1953, the end of 10ER production. Maybe the first/early arbor had no key way.
Total length 3 1/8, shaft length 1 5/8, keyed shaft and washer.
10erarbor.JPG
and with the blade mounted.
arborandblade.JPG
To quote..."The collars, one 3/4" thick and two 3/16" thick, are machined and counterbored to assure clamping fit."
Quite obviously your arbor will not accommodate a second thin spacer. This tells me there are at least two different arbors for the 10ER. So again maybe the very first ones did not have a key way.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: Arbors
It would seem they changed the design a few times. I was just looking at the 10e preliminary manual and it describes the saw arbor as having two threaded washers. The '52 catalog description is the same as in '53 that you quotedjsburger wrote:Interesting! The 1953 accessory catalog lists a 3/4" spacer and TWO 3/16" spacers. The two 3/16" spacers are clearly visible in the picture of the arbor.rpd wrote:This is the arbor that came with my 10ER, it is what I use with my saw blade.jsburger wrote: First, I think you are just missing the thick washer. As for the key way. Does anyone know if the 10ER arbor had a key way. Looking at the 10ER accessory catalog that arbor is basically the same as the current arbor but the catalog says the thick washer is 3/4". Does anyone have a known 10ER arbor and does it have a key way. It is hard to tell from the picture in the catalog but using a magnifying glass it looks like it has a key way. However, the catalog is dated 1953, the end of 10ER production. Maybe the first/early arbor had no key way.
Total length 3 1/8, shaft length 1 5/8, keyed shaft and washer.
10erarbor.JPG
and with the blade mounted.
arborandblade.JPG
To quote..."The collars, one 3/4" thick and two 3/16" thick, are machined and counterbored to assure clamping fit."
Quite obviously your arbor will not accommodate a second thin spacer. This tells me there are at least two different arbors for the 10ER. So again maybe the very first ones did not have a key way.
The '54 catalog only shows arbors in the Mk5 section but under saw blades in the 10er section it says to use the 5/8 arbor , this is the first one that mentions the keyed washer, but the picture is the same as previous years. Something to take into account is that they did not have separate saw and accessory arbors, so for saw blades you would use the 3/4 washer and one 3/16 washer, and for thicker accessories (wire/ buffing/ grinding wheels etc) you would use the two 3/16 only, one suspects that the unused one would get lost over the years.
Perhaps the keyed washer was included all along and just wasn't mentioned in the earlier catalogs,(they don't mention the nut either).
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
Re: Arbors
Update. Since my last post I have acquired a third 10ER.
The arbor that came with this one does not have a slot or keyed washer, and its set screw takes a smaller allen key.
A side note, on this one both washers are steel, on the one with the slot the 3/4" washer is aluminum.
Also note previous owner had the blade mounted wrong. thin washer, thick washer (recess on the wrong side), blade, lock washer (not oem), nut.
The arbor that came with this one does not have a slot or keyed washer, and its set screw takes a smaller allen key.
A side note, on this one both washers are steel, on the one with the slot the 3/4" washer is aluminum.
Also note previous owner had the blade mounted wrong. thin washer, thick washer (recess on the wrong side), blade, lock washer (not oem), nut.
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,