The original leg holes locations can varies by as much as 1/4" between legs where the holes are drilled in the legs over the many years. Using clamps to hold the caster assembly to get the desired proper height for the caster is the best way. I averaged the different distances to make a template that everyone can use.dusty wrote:Yes, it is posted here somewhere. I have posted measurements as well.
However, this installation is somewhat dependent on the wheels that you use. The wheel assemblies may be different heights from different manufacturers - so proceed slowly - it is difficult to undrill holes..
Mark V 3" Caster Installation
Moderators: HopefulSSer, admin
Bill Mayo bill.mayo@verizon.net
Shopsmith owner since 73. Sell, repair and rebuild Shopsmith, Total Shop & Wood Master headstocks, SPTs, attachments, accessories and parts. US Navy 1955-1975 (FTCS/E-8)
Shopsmith owner since 73. Sell, repair and rebuild Shopsmith, Total Shop & Wood Master headstocks, SPTs, attachments, accessories and parts. US Navy 1955-1975 (FTCS/E-8)
Steve -skou wrote:Gene, JPG, you 2 owe me a new keyboard!
I just spewed uh, "milk" all over it, through my nose.
steve
Today is National Martini Day, you shouldn't be drinking "milk".
Mike
I wasn't.
"Milk" is a euphemism.
I'm actually imbibing "cerveza." (Look it up.)
Oh, today is my day off, so I'm allowed. Also,
since I'm listening to a Jimmy Buffett concert
(Live) the drink of the day should be a
Margartia, from Margaritaville!
(Except tequila gives me the "technicolor
yawns.") Rum is more to my liking.
Sorry for the hijack!
Oh, for everyone (except Fred Sheldon)
http://www.margaritaville.com/radio_listen.html
Fred should already have this!
steve
- "Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
Today is National Martini Day
Shucks, I just thought it was June Teenth Day!!! Plus out of Martini fixens today and just had iced coffee tonight.
Shucks, I just thought it was June Teenth Day!!! Plus out of Martini fixens today and just had iced coffee tonight.
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
- "Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
Thanks skuo, for the new streaming, I was listening to my German music from Denver. Try it.
http://www.grtvd.com/
http://www.grtvd.com/
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
- dusty
- Platinum Member
- Posts: 21371
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
claimdude wrote:Are the truss head bolts used to attach the casters to the legs 18-8 in size?
Thanks
Jack
Jack,
I am not certain that I understand your question but I'm going to give it a go.
My caster assemblies are attached to the legs using either 1/4"-20x1" truss heads bolts and the appropriate 1/4"-20 hex nut.
On some of the locations, I may have used 1/4"-20x3/4" bolts. The nylon spacers sorta dictate the length.
With regard to your reference to 18-8: I do not believe that is a size reference but rather a reference to the type of stainless steel used.
http://www.portlandbolt.com/faqs/18-8-304-and-316-stainless-steel/
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Re: Mark V 3" Caster Installation
Bill,
Your tip was a life saver I was able to do the upgrade all by myself.
Used the SS Castor upgrade with the metal locating tool, this was easier than I thought.
Thanks again for the good Ideas,
Dan
Your tip was a life saver I was able to do the upgrade all by myself.
Used the SS Castor upgrade with the metal locating tool, this was easier than I thought.
Thanks again for the good Ideas,
Dan
- ChrisNeilan
- Platinum Member
- Posts: 1461
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Re: Mark V 3" Caster Installation
Dan, I am sure Bill would have liked your comment. He was one of the best on this forum. Unfortunately he passed away several months ago. Left a good legacy.dmfotoman wrote:Bill,
Your tip was a life saver I was able to do the upgrade all by myself.
Used the SS Castor upgrade with the metal locating tool, this was easier than I thought.
Thanks again for the good Ideas,
Dan
Chris Neilan
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe