It looks good. I think.
Repairing Model 510 Castings, A Question
Moderators: HopefulSSer, admin
- dusty
- Platinum Member
- Posts: 21371
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Repairing Model 510 Castings, A Question
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Re: Repairing Model 510 Castings, A Question
I think so too.dusty wrote:It looks good. I think.
![Cool :cool:](./images/smilies/cool.gif)
![Smile :)](./images/smilies/smile.gif)
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
- chapmanruss
- Platinum Member
- Posts: 3488
- Joined: Tue Aug 26, 2014 8:16 pm
- Location: near Portland, Oregon
Re: Repairing Model 510 Castings, A Question
Although to late for Dusty to use I had a Greenie I restored and the base had a broken out hole. Actually the end one that I repaired with aluminum rod brazed in to fill the space than ground down to match the original profile. Could also be done as Everett suggested by someone with a MIG or TIG welder that is set up for aluminum welding.
Dusty,
I would suggest that you put the new holes as close to but not to close to the original holes as possible to maintain the strength of the original design. On the end maybe a new hole on either side of the original would be good. New hole locations as shown by the red arrows in the diagram below Remember using this as a workbench frame it was designed to carry a certain amount of weight but not designed for repeated impacts/hammering.
Dusty,
I would suggest that you put the new holes as close to but not to close to the original holes as possible to maintain the strength of the original design. On the end maybe a new hole on either side of the original would be good. New hole locations as shown by the red arrows in the diagram below Remember using this as a workbench frame it was designed to carry a certain amount of weight but not designed for repeated impacts/hammering.
Russ
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
- dusty
- Platinum Member
- Posts: 21371
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Repairing Model 510 Castings, A Question
This workbench project is going well even though I have mixed feelings about the avenue I took for repair. I could easily have used the countersinks as they were...(but I did not). I have three more holes to fill and some prep work on the ones I have already done.
Then the question...redrill before paint or no.
Then the question...redrill before paint or no.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
- JPG
- Platinum Member
- Posts: 34643
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Repairing Model 510 Castings, A Question
I think drill before painting.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Repairing Model 510 Castings, A Question
JPG wrote:I think drill before painting.
+1 Always
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT