Greetings all. Have some desert ironwood along with a lot of river birch.
Need to cut up. Understand a carbide tip bandsaw blade is required.
Tried looking up Lenox carbide bandsaw blades without any luck. The Lenox website has at least half a dozen different types of carbide blades. Didn't see any 72 1/2" blades.
Anyone know a source & what size blade is the best?
Thanks,
Tony
Carbide Tip Bandsaw Blade
Moderators: HopefulSSer, admin
Re: Carbide Tip Bandsaw Blade
Timberwolf blades. https://timberwolfblades.com/backhertz wrote:Greetings all. Have some desert ironwood along with a lot of river birch.
Need to cut up. Understand a carbide tip bandsaw blade is required.
Tried looking up Lenox carbide bandsaw blades without any luck. The Lenox website has at least half a dozen different types of carbide blades. Didn't see any 72 1/2" blades.
Anyone know a source & what size blade is the best?
Thanks,
Tony
They will make anything you need and they know Shopsmith. It is cheaper to buy direct from them than anywhere else I have looked.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: Carbide Tip Bandsaw Blade
Don't know which blade is best for your purpose. However, this place sells Lennox blades to size, and the price is very good. https://www.bandsawbladesdirect.com/
- BuckeyeDennis
- Platinum Member
- Posts: 3696
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: Carbide Tip Bandsaw Blade
Here’s a thread from several years ago where this was discussed.
https://www.shopsmith.com/ss_forum/view ... 18&t=15306
Per the Lenox “Guide to Bandsawing”, it looks like the Lenox Tri-Master is the best blade for the job. I cut & pasted a couple of impressive user reviews in that same thread. At the time, Highland Woodworking sold them in Shopsmith size for $103, but they no longer carry them.
https://www.lenoxtools.com/Guides/LENOX ... Sawing.pdf
As Dansmith said, you can buy them from BandSawBladesDirect.com, in whatever width and length you want. A 1/2” x 72-1/2” Tri-Master blade is priced at about $119. You can Google “Lenox Tri-Master” for more vendors and user reviews.
https://www.bandsawbladesdirect.com/len ... saw-blades
I’ve been wanting to get one for myself, but I just haven’t had any projects that would justify the price tag.
https://www.shopsmith.com/ss_forum/view ... 18&t=15306
Per the Lenox “Guide to Bandsawing”, it looks like the Lenox Tri-Master is the best blade for the job. I cut & pasted a couple of impressive user reviews in that same thread. At the time, Highland Woodworking sold them in Shopsmith size for $103, but they no longer carry them.
https://www.lenoxtools.com/Guides/LENOX ... Sawing.pdf
As Dansmith said, you can buy them from BandSawBladesDirect.com, in whatever width and length you want. A 1/2” x 72-1/2” Tri-Master blade is priced at about $119. You can Google “Lenox Tri-Master” for more vendors and user reviews.
https://www.bandsawbladesdirect.com/len ... saw-blades
I’ve been wanting to get one for myself, but I just haven’t had any projects that would justify the price tag.
- ChrisNeilan
- Platinum Member
- Posts: 1461
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Re: Carbide Tip Bandsaw Blade
Why is a carbide blade required? I have cut those before with regular blades.
Chris Neilan
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
-
- Platinum Member
- Posts: 1564
- Joined: Wed Feb 05, 2014 11:57 am
- Location: Las Vegas NV
Re: Carbide Tip Bandsaw Blade
I have never purchased one of the carbide blades but have used a resaw bandsaw that had one on it. The carbide means it just stays sharper longer. The cost is about 3-4 times that of a conventional blade but they tend to stay sharper for much longer than that. If you are going to resaw a large amount of wood they probably are worth the cost. If the amount of wood is fairly small then just buying a new conventional blade for that job is probably more cost effective. One other consideration if you are resawing very expensive wood for veneer purposes is the kerf on the carbide blades are much wider so you will get less end product.
Paul
Paul