phone  (937) 890-5197

Shopsmith Forums

%nbsp;

96 posts • Jump to page: 1 6 7 8 9 10

Bad news. I went to Eurton Electric with the motor/brush holder. They informed me that what is on their website is the selection they have available. I checked their part # BH4050 against my brush holder, and the BH4050 is for a wider brush size, as well as the brass portion being too long. Time to keep looking, it seems.

Post a reply  Reply with quote 

Re: Can a 12" Planer w/o feed motor be converted to manual feed?

#263818 by everettdavis » Sun Oct 20, 2019 12:07 am

I am still on the trail. Having to obtain and document the 4 known types of Planer Feed Motors and I just encountered a 5th type that is out there... Negotiating to acquire it. Don't need it, but need it to document.

Still looking for the carbon brush holder and correct carbon brushes...

There are a bunch of holders out there, and it makes no sense to me at all that Shopsmith would have built a custom reduction gear motor for the planer when so many manufactured pieces of other equipment in other industries used very similar motors in other applications.

As you can tell from the attached photo, nailing down the holder(s) is a challenge, but I do not believe it is impossible, just hard. Once I find the holder, the appropriate brush to fill it should be far simpler.

Everett
Extruded Cartridge Brush Holders.png
Extruded Cartridge Brush Holders.png (258.68 KiB) Viewed 9005 times

Post a reply  Reply with quote 

Here is a photo of the 5th type of Planer Feed Motor.

I plan to acquire it and the controller for it and will document it in detail in coming months.

Everett
02B4EC68-2F4E-40CF-AF17-D2D6912E7968.jpeg
02B4EC68-2F4E-40CF-AF17-D2D6912E7968.jpeg (306.72 KiB) Viewed 8919 times
Last edited by everettdavis on Wed Nov 27, 2019 10:32 am, edited 1 time in total.

Post a reply  Reply with quote 

Re: Can a 12" Planer w/o feed motor be converted to manual feed?

#265047 by everettdavis » Wed Nov 27, 2019 10:31 am

After working with the seller and obtaining more photos, it was apparent that the motor was not for the Planer as it had no reduction gearing. On questioning he revealed that it was in a batch of stuff that he sold all the other parts from.

On further analysis and a confirming photo from John Burger this week, I verified that it was a stand alone scroll saw motor.

I still purchased it and the controller which appears to be the same as one of the planer motor control types.

My interest remains in the brush holders and motor brushes which just may fit a VonWeise planer feed motor, or could be adapted to.

Everett

Post a reply  Reply with quote 

Some spectacularly good information here (thanks Everett) on parts for the feed motors.
Has anyone done any research on whether there are any complete motors out there new? I'm sure if they are they are pricey but if we have a motor that will work we might find a cheap clone somewhere too.
All I know is that SS no longer carries them. But there has to be something out there that will fit...

Post a reply  Reply with quote 

This site shows the planer motor available under a different number than in my old book. It isn't cheap, but likely available.
https://www.shopsmith.com/ownersite/ite ... tem=513731

Post a reply  Reply with quote 

Who is online

Users browsing this forum: Google [Bot] and 184 guests

Board indexDelete all board cookies

Welcome to Shopsmith. Please fill in this form and we'll send you more information and special offers for the Shopsmith MARK 7 and other woodworking topics.

Subscribe to our mailing list

* indicates required