Shopsmith Jacobs 3326 Chuck Key Needed

Forum for Maintenance and Repair topics. Feel free to ask questions or contribute.

Moderators: HopefulSSer, admin

User avatar
hobbyist
Gold Member
Posts: 23
Joined: Wed Aug 16, 2006 12:46 am
Location: Texas
Contact:

Post by hobbyist »

Here's two more for the chuck library...

Image

Left:
Cushman C13LS, JAPAN
Cap. 5/64 - 1/2
Jacobs KK chuck key fits (I don't have the original Cushman key)

My machine is a 1981 model that I purchased used. I believe this was its original chuck supplied by Shopsmith.

Right:
Jacobs 3326
Hartford Conn., Made in USA
Cap. 5/64 - 1/2
Jacobs K 32 H chuck key

I bought this chuck on eBay last year. It's a beautiful old chuck that looks to have never previously been used. Interestingly, the chuck key doubles as a 5/32" hex wrench. I wonder if these keys were specially made for Shopsmith long ago. This is an outstanding chuck and reliably locks up with almost no runout every time.

Ray
james.miller
Gold Member
Posts: 303
Joined: Thu Jul 20, 2006 2:16 pm

Post by james.miller »

I just checked an old 3326 chuck that came with a 55 greenie.

The key is a K32H with hex rod for a handle.

This chuck will not close down far enough to chuck up a 1/16" drill bit.
Jim in Tucson
james.miller
Gold Member
Posts: 303
Joined: Thu Jul 20, 2006 2:16 pm

Post by james.miller »

Also check out this post http://www.shopsmith.net/forums/showthread.htm?t=2941

Jacobs still offers a version of it, the 3326A, it won't close on a 1/16" bit either.
Jim in Tucson
User avatar
hobbyist
Gold Member
Posts: 23
Joined: Wed Aug 16, 2006 12:46 am
Location: Texas
Contact:

Post by hobbyist »

james.miller wrote:This chuck will not close down far enough to chuck up a 1/16" drill bit.
For drill bits less than 5/64", I like to use a Starrett Pin Vise (with the knurled pin vise handle cut off). These pin vises are designed for chucking, though the Shopsmith chuck bore is not deep enough to accommodate the length of the handle.

Here's my modified 240A pin vise...

Image

Image

Ray
User avatar
bucksaw
Gold Member
Posts: 282
Joined: Mon Jan 12, 2009 7:17 pm
Location: Boise, ID

Post by bucksaw »

It's too bad Shopsmith did not keep a master list of all the Chuck and Keys shipped over the years. It would have save us some hassle.
Dave - Idaho
Greenie S#261612 - Mar 1954 / Greenie S#305336 - Oct 1955 / Gray S#SS1360 - ?

"Why do we drive on parkways and park on driveways?" :cool:
User avatar
bucksaw
Gold Member
Posts: 282
Joined: Mon Jan 12, 2009 7:17 pm
Location: Boise, ID

Post by bucksaw »

I keep one of these Makita chucks on hand for small bits.

Image
Dave - Idaho
Greenie S#261612 - Mar 1954 / Greenie S#305336 - Oct 1955 / Gray S#SS1360 - ?

"Why do we drive on parkways and park on driveways?" :cool:
alaskanexile
Gold Member
Posts: 60
Joined: Thu Jul 20, 2006 3:38 pm
Location: Orlando

Post by alaskanexile »

I have a Jacobs 3326 chuck with a K32 key. Believe it came orginal with my 56 greenie. Although clearly stamped on the chuck is, 4/64 - 1/2", I have many time successfully clamped a 1/16 bit in it. Now you guys have me wondering what's in there hanging unto that bit.
Roger
charlese
Platinum Member
Posts: 7501
Joined: Fri Dec 08, 2006 10:46 pm
Location: Lancaster, CA

Post by charlese »

I don't know much about the differences in dill chucks, but I have successfully chucked up a #6 bit in my Shopsmith chuck. This is a wire drill bit that is a lot smaller than 1/16". I used it for drilling pilot holes for staples in shutter louvers.

Next time I'll have to strongly consider a Starrett Pin Vise.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
charlese
Platinum Member
Posts: 7501
Joined: Fri Dec 08, 2006 10:46 pm
Location: Lancaster, CA

Post by charlese »

charlese wrote:... I have successfully chucked up a #6 bit in my Shopsmith chuck. This is a wire drill bit that is a lot smaller than 1/16". I used it for drilling pilot holes for staples in shutter louvers.
Whoops!!! Correction! - - It was a #56 wire gauge bit, not a #6. The bit measures .046" But now I know about a Starrett Pin vise.

With what I read, I'm surprised the Shopsmith chuck worked, but it did nicely.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
User avatar
horologist
Gold Member
Posts: 431
Joined: Sat Dec 22, 2007 6:36 pm
Location: Melrose, FL

Post by horologist »

I have had mixed results with the pin vise mounted in the Jacobs chuck arrangement. In general the accumulated errors can wreak havoc on both your work and the drill bit. Chinese pin vises will not work here! I have an Albrecht sensitive feed chuck (missing the outer sleeve) that I use. These chucks appear regularly on ebay with a 1/2" shaft. This would probably work well with the 1/2" router bit chuck. For holes near 1/16" it really isn't that critical and odds are a Starrett pin vise would rarely give trouble. I frequently use the wire gauge bits between 61 and 80 and have pivot drills down to 0.1mm (0.004").


[ATTACH]3179[/ATTACH]
Attachments
albrecht.jpg
albrecht.jpg (39.68 KiB) Viewed 13988 times
The best equipped laundry room in the neighborhood...
Post Reply