Shopsmith Jacobs 3326 Chuck Key Needed
Moderators: HopefulSSer, admin
Here's two more for the chuck library...
Left:
Cushman C13LS, JAPAN
Cap. 5/64 - 1/2
Jacobs KK chuck key fits (I don't have the original Cushman key)
My machine is a 1981 model that I purchased used. I believe this was its original chuck supplied by Shopsmith.
Right:
Jacobs 3326
Hartford Conn., Made in USA
Cap. 5/64 - 1/2
Jacobs K 32 H chuck key
I bought this chuck on eBay last year. It's a beautiful old chuck that looks to have never previously been used. Interestingly, the chuck key doubles as a 5/32" hex wrench. I wonder if these keys were specially made for Shopsmith long ago. This is an outstanding chuck and reliably locks up with almost no runout every time.
Ray
Left:
Cushman C13LS, JAPAN
Cap. 5/64 - 1/2
Jacobs KK chuck key fits (I don't have the original Cushman key)
My machine is a 1981 model that I purchased used. I believe this was its original chuck supplied by Shopsmith.
Right:
Jacobs 3326
Hartford Conn., Made in USA
Cap. 5/64 - 1/2
Jacobs K 32 H chuck key
I bought this chuck on eBay last year. It's a beautiful old chuck that looks to have never previously been used. Interestingly, the chuck key doubles as a 5/32" hex wrench. I wonder if these keys were specially made for Shopsmith long ago. This is an outstanding chuck and reliably locks up with almost no runout every time.
Ray
-
- Gold Member
- Posts: 303
- Joined: Thu Jul 20, 2006 2:16 pm
-
- Gold Member
- Posts: 303
- Joined: Thu Jul 20, 2006 2:16 pm
Also check out this post http://www.shopsmith.net/forums/showthread.htm?t=2941
Jacobs still offers a version of it, the 3326A, it won't close on a 1/16" bit either.
Jacobs still offers a version of it, the 3326A, it won't close on a 1/16" bit either.
Jim in Tucson
For drill bits less than 5/64", I like to use a Starrett Pin Vise (with the knurled pin vise handle cut off). These pin vises are designed for chucking, though the Shopsmith chuck bore is not deep enough to accommodate the length of the handle.james.miller wrote:This chuck will not close down far enough to chuck up a 1/16" drill bit.
Here's my modified 240A pin vise...
Ray
-
- Gold Member
- Posts: 60
- Joined: Thu Jul 20, 2006 3:38 pm
- Location: Orlando
I don't know much about the differences in dill chucks, but I have successfully chucked up a #6 bit in my Shopsmith chuck. This is a wire drill bit that is a lot smaller than 1/16". I used it for drilling pilot holes for staples in shutter louvers.
Next time I'll have to strongly consider a Starrett Pin Vise.
Next time I'll have to strongly consider a Starrett Pin Vise.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Chuck in Lancaster, CA
Whoops!!! Correction! - - It was a #56 wire gauge bit, not a #6. The bit measures .046" But now I know about a Starrett Pin vise.charlese wrote:... I have successfully chucked up a #6 bit in my Shopsmith chuck. This is a wire drill bit that is a lot smaller than 1/16". I used it for drilling pilot holes for staples in shutter louvers.
With what I read, I'm surprised the Shopsmith chuck worked, but it did nicely.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Chuck in Lancaster, CA
- horologist
- Gold Member
- Posts: 431
- Joined: Sat Dec 22, 2007 6:36 pm
- Location: Melrose, FL
I have had mixed results with the pin vise mounted in the Jacobs chuck arrangement. In general the accumulated errors can wreak havoc on both your work and the drill bit. Chinese pin vises will not work here! I have an Albrecht sensitive feed chuck (missing the outer sleeve) that I use. These chucks appear regularly on ebay with a 1/2" shaft. This would probably work well with the 1/2" router bit chuck. For holes near 1/16" it really isn't that critical and odds are a Starrett pin vise would rarely give trouble. I frequently use the wire gauge bits between 61 and 80 and have pivot drills down to 0.1mm (0.004").
[ATTACH]3179[/ATTACH]
[ATTACH]3179[/ATTACH]
- Attachments
-
- albrecht.jpg (39.68 KiB) Viewed 14167 times
The best equipped laundry room in the neighborhood...